DIGITAL-LOGIC MSB900L Instrukcja Użytkownika Strona 53
- Strona / 66
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0
53
9. JUMPER LOCATIONS ON THE BOARD
The following figure shows the location of all jumper blocks on the MSB900/L board. The numbers shown in
this figure are silk screened on the board so that the pins can easily be located. This chapter refers to the
individual pins for these jumpers. The default jumper settings are indicated with asterisks.
Be careful: some jumpers are soldering bridges; you will need a miniature soldering station with a vacuum
pump.
9.1. The Jumpers on MSB900/L
Settings written in bold are defaults.
Jumper Structure 1-2 / open 2-3 / closed
Remarks
J1 CompactFlash master Slave
Master
J2 Autostart function Enabled N/A
1)
J3 Disconnect Battery
Disabled
N/A
J4 Disconnect CMOS EEPROM
Disabled
N/A
1) With the autostart function enabled, the system will start booting up within 2 seconds after the power
supply is turned on.
9.2. Reload Default BIOS Settings
To reload default BIOS settings when the system refuses to boot after defective BIOS settings have been
made please proceed as follows.
• Turn off the system.
• Remove J3 on MSB900 or disconnect the optional external battery on the MSB900L.
• Remove J4.
• Turn on the system and enter the BIOS setup menu.
• Close J4 and J5 or attach the optional external battery.
• Choose save and exit in the BIOS setup menu.
- MSB900/L 1
- COPYRIGHT 2
- 2008 BY DIGITAL-LOGIC AG 2
- REVISION HISTORY: 2
- Table of Contents 3
- 1. PREFACE 5
- 1.5. Recycling Information 6
- 1.6. Technical Support 6
- 1.8. Explanation of Symbols 7
- 1.10. For Your Safety 9
- 1.11. RoHS Commitment 9
- 1.11.3. WEEE Application 10
- 1.12. Swiss Quality 11
- 2. OVERVIEW 12
- 2.3. MSB900 Block Diagram 13
- 2.7.1. MSB900/L 17
- 3. BUS SIGNALS 23
- 4. BIOS HISTORY 24
- ETAILED SYSTEM DESCRIPTION 25
- 5.1. Power Requirements 25
- 5.2. Boot Time 25
- 5.3. CPU, Boards and RAMs 26
- 5.4. Interfaces 26
- 5.5. Controllers 27
- 5.6. Timers and Counters 28
- 5.7. CMOS RAM Map 29
- CMOS Map 30
- CMOS Map continued 31
- 5.9. Memory & I/O Map 35
- 5.9.2. System I/O map 36
- Continued… 37
- 6. VGA 40
- 7. VIDEO INPUT 41
- Note 45
- Attention! 45
- UMPER LOCATIONS ON THE BOARD 53
- 10. CABLE INTERFACES 55
- Connector X61 56
- Connector X39 57
- 11. THERMAL SPECIFICATIONS 58
- 12. ASSEMBLY VIEWS 59
- 14. PXE-LICENSE ORDER 64
- 15. INDEX 65
Atec Fluke-OptiView-XG podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Ekwipunek Atec Fluke-OptiView-XG.
Dostarczamy 1 pdf podręczników Atec Fluke-OptiView-XG do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji